DESIGN · BUILD · AUTOMATE
ARVADA SERVICES
EV Charger Install — Level 2 in Arvada
Licensed ev charger install — level 2 services for Arvada and Jefferson/Adams County. Charge at home. Every night..
- Full Design Lifecycle
- Construction & Tenant Finish
- Smart Home · A/V · Edge Compute
Charge at home. Every night.
EVERY PROJECT STARTS WITH DESIGN
Local Service
EV Charger Install — Level 2 Services in Arvada, Colorado
Autotelic provides professional ev charger install — level 2 services throughout Arvada and the surrounding Jefferson/Adams County area. Level 2 EV charger installation across the Denver metro — 240V dedicated circuit, NEMA 14-50 outlet, hardwired units, and load management. Whether you're in Arvada (historic Olde Town and rapid growth) or nearby communities, our team delivers quality workmanship backed by Colorado licensing and full insurance coverage.
Permits & Licensing
Permits in Arvada
Arvada building permits are issued by Building Services, and the city notes that unpermitted work can jeopardize a contractor's licensing as well as a property's resale value. Permit applications, inspection scheduling, and status checks are handled through the separate Arvada Permits (eTRAKiT) site. Authority: City of Arvada — Building Services.
Permit Thresholds
Arvada permit thresholds
- Code reference
- Arvada requires building permits for most residential construction, alteration, repair, enlargement, replacement, equipment installation, use/occupancy changes, and demolition work, per the City’s Building Permits page and Chapter 18 of the Arvada City Code (which adopts the 2024 International ResOrdinance No. 4921
- Code reference
- This is assessed in lieu of sales tax on construction materials used in Arvada (Arvada Municipal Code § 98-84).§ 98-84
- Code reference
- A separate 2026 Building Fee Schedule PDF is referenced but not detailed on the main pages.
- Code reference
- For the most current or project-specific details (including any local amendments to the 2024 IRC that might address minor/exempt work or structural thresholds), contact the Arvada Building Safety Division or check the adopted codes on the City website, as published information emphasizes case-by-cas
Codes are amended regularly — verify current requirements with City of Arvada — Building Services.
Energy Code
Arvada energy code quick facts
- Code reference
- Arvada, Colorado, has adopted the Colorado Low Energy Carbon Code (or Model Low Energy and Carbon Code/MLECC/LECC), based on the 2024 International Energy Conservation Code (IECC), with no additional local energy-code amendments noted beyond the state model. This applies alongside the 2024 Inter
- Code reference
- Adoption occurred via City Council action on March 24, 2026 (effective for permits submitted on or after approximately July 1, 2026).
- Code reference
- Arvada (Climate Zone 5B) does not use the Denver Green Code or Energize Denver program.
- Code reference
- For remodels and additions, the modified/new portions generally must comply with the current code (per IECC/LECC Sections C502/C503 or R502/R503 equivalents) without necessarily triggering updates to unmodified existing systems.
- Code reference
- Key prescriptive requirements (drawn from the 2024 IECC residential provisions as adopted in the Colorado LECC; values for CZ 5; relevant to new or modified envelope elements in additions/remodels):
- Ceiling/attic insulation
- Minimum R-49 (Table R402.1.3 / equivalent in LECC).
- Wood-frame above-grade wall insulation
- Options include R-20 + R-5 ci, R-13 + R-10 ci, or equivalent assembly U-factor ≤ 0.045 (or reduced options such as R-20 cavity with additional efficiency credits per R408); see Table R402.1.2/R402.1.3.
- Air leakage (blower-door testing)
- Maximum 3.0 ACH50 at 50 Pa for the tested dwelling unit or building under the prescriptive path in CZ 3–5 (R402.5.1.3 / equivalent).
Codes are amended regularly — verify current requirements with City of Arvada — Building Services.
Zoning & Dimensional Standards
Setback & dimensional standards in Arvada
Zone-district dimensional standards for Arvada, quoted verbatim from the Arvada Land Development Code. Knowing your lot's district — and its setbacks, height, and coverage limits — is where every feasibility conversation starts.
RN-12.5setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 30 ft. |
| Side Interior Setback (min) | 10 ft. |
| Rear Setback (min) | 15 ft. |
| Building Coverage (max) | 35% |
| Building Height (max) | 28 ft. |
| Lot Area (min) | 12,500 sf. |
| Lot Width (min) | 100 ft. |
Arvada Land Development Code RN-12.5 setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
RN-32.5setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 30 ft. |
| Side Interior Setback (min) | 15 ft. |
| Rear Setback (min) | 15 ft. |
| Building Coverage (max) | 25% |
| Building Height (max) | 35 ft. |
| Lot Area (min) | 32,500 sf. |
| Lot Width (min) | 100 ft. |
Arvada Land Development Code RN-32.5 setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
RN-4setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 18 ft. |
| Side Interior Setback (min) | 5 ft. |
| Rear Setback (min) | 10 ft. |
| Building Coverage (max) | 40% |
| Building Height (max) | 28 ft. |
| Lot Area (min) | 4,000 sf. |
| Lot Width (min) | 40 ft. |
Arvada Land Development Code RN-4 setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
RN-6setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 18 ft. |
| Side Interior Setback (min) | 5 ft. |
| Rear Setback (min) | 10 ft. |
| Building Coverage (max) | 40% |
| Building Height (max) | 28 ft. |
| Lot Area (min) | 6,000 sf. |
| Lot Width (min) | 50 ft. |
Arvada Land Development Code RN-6 setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
RN-7.5setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 20 ft. |
| Side Interior Setback (min) | 7.5 ft. |
| Rear Setback (min) | 10 ft. |
| Building Coverage (max) | 40% |
| Building Height (max) | 28 ft. |
| Lot Area (min) | 7,500 sf. |
| Lot Width (min) | 75 ft. |
Arvada Land Development Code RN-7.5 setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
RN-Dsetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 18 ft. |
| Side Interior Setback (min) | 5 ft. |
| Rear Setback (min) | 10 ft. |
| Building Coverage (max) | 40% |
| Building Height (max) | 28 ft. |
| Lot Area (min) | 6,000 sf. |
| Lot Width (min) | 60 ft. |
Arvada Land Development Code RN-D setback standards (2-1-3-3 Table 2-1-3-3A (RN)) — effective 2025-12-16 · View the code
Verify current requirements with the jurisdiction — informational reference only. Standards vary by overlay, lot, and use; we confirm the exact rules for your property during feasibility.
text
What a Level 2 install actually covers
A Level 2 EV charger install adds a dedicated 240-volt branch circuit and mounts a wall, pedestal, or hardwired charging unit at the parking location. Typical scope includes a site assessment and NEC Article 220 load calculation on the existing service, permit application with the local authority, circuit rough-in, charger mounting and termination, functional testing, and final inspection. If the panel cannot support the continuous EV load, the scope may expand to a service or sub-panel upgrade before the charger circuit is added.
text
Electrical scope and equipment classes
Most residential Level 2 units land on a 40- to 50-amp double-pole breaker. A 48-amp continuous charger is commonly planned on a 60-amp circuit because Colorado follows the 2020 NEC requirement to size new continuous loads at 125 percent. Wiring is typically copper sized to the breaker and charger rating—often 6 AWG copper for a 48-amp unit—run in approved methods and protected from physical damage, frequently in conduit for exposed or outdoor segments. Connection is either hardwired or a NEMA 14-50 receptacle; hardwiring is usually preferred outdoors for weather resistance. GFCI protection is required for most 240V Level 2 charging circuits. Outdoor units should carry at least a NEMA 3R enclosure rating, with NEMA 4 preferred for Denver hail, freeze-thaw, and wind-driven rain. Common equipment classes include Wi-Fi-capable residential wall connectors and flexible amperage units such as ChargePoint Home Flex, Grizzl-E, Emporia, and Tesla Wall Connector, selected to match vehicle inlet, cable reach, and scheduled-charging needs.
text
Mounting locations and site conditions
Exterior wall mounts near the garage or panel path are the simplest when structure and parking alignment allow. Pedestal mounts serve driveways or parking pads without a usable wall and usually need a concrete footing. Detached garages or across-yard parking require trenched conduit from the main panel or a suitably placed sub-panel. Placement should balance cable reach to the charge port, protection from traffic and snow storage, and distance back to the electrical source so conductor length and voltage drop stay practical.
text
Denver permits, codes, and inspections
In the City and County of Denver, an electrical permit is required for Level 2 charger work through Community Planning and Development, with a final inspection after install. Inspectors look for correct grounding, conductor sizing, overcurrent protection, GFCI where required, and work matching the permitted scope. Installations must follow NEC Article 625 for EV power transfer systems and NEC Article 220 load-calc methods for panel capacity. The Denver Energy Code also drives EV-ready provisions on many new garages and carports: a 240-volt, 40-amp branch circuit path, a dedicated EV-ready breaker space, and a receptacle or charging connection at the parking space. Metro suburbs follow their own building departments and may apply state or local amendments, so jurisdiction is confirmed before rough-in.
text
Panel capacity and when upgrades enter the job
Older Denver-metro housing often still has 100-amp service. A proper load calculation determines whether spare capacity exists for a continuous Level 2 load or whether a panel upgrade, feeder change, or sub-panel is required first. Skipping that step risks nuisance tripping, rejected inspection, or an undersized install that cannot support the charger rating the vehicle needs. Xcel Energy and other programs sometimes offer rebates on qualifying Level 2 equipment; rebate paperwork is separate from the electrical permit and depends on current utility rules and product eligibility.
text
How Autotelic runs the project
Autotelic is a municipally licensed Denver general contractor. For Level 2 EV charger work, we coordinate licensed specialty electrical trades for load calculation, circuit installation, panel work when needed, permit handling, and inspection readiness. That keeps design-build sequencing clear when charger install ties into garage remodels, driveway work, pedestal foundations, or broader electrical service changes.
FAQ
Common questions
Who handles the electrical permits and licensing?
Autotelic is a municipally licensed Denver general contractor and coordinates licensed specialty electrical trades for Level 2 charger circuits, panel evaluations, and related service work. The electrical permit is pulled with the local authority—in Denver, Community Planning and Development—and the finished install is left ready for required inspection.
Do I need a dedicated circuit for a Level 2 charger?
Yes. Level 2 equipment requires a dedicated 240-volt branch circuit with overcurrent protection sized to the charger rating and wire ampacity. Sharing the circuit with other loads is not acceptable under standard EV charging practice and code expectations.
Hardwired or NEMA 14-50—which is better outdoors?
Both are used, but hardwiring is generally more weather-resistant for permanent outdoor mounts. A NEMA 14-50 receptacle can be appropriate indoors or where a cord-and-plug setup is specified. Enclosure rating, GFCI requirements, and local inspection expectations guide the final choice.
Will my existing panel support a Level 2 charger?
Only a load calculation can answer that. Many older homes with 100-amp service need a panel or sub-panel upgrade before a 40- to 60-amp continuous EV circuit is added. The assessment should happen before equipment is purchased and before a final scope is locked.
What outdoor rating matters in Denver weather?
Use a charger listed for outdoor installation with at least a NEMA 3R enclosure; NEMA 4 is preferred where driving rain, dust, and hail exposure are concerns. Mounting height, cable management, and protection from vehicle paths and snow storage matter as much as the enclosure rating.
Are utility rebates part of the install?
Sometimes. Programs such as Xcel Energy rebates may apply to qualifying Level 2 equipment and installations, but eligibility, product lists, and documentation change. Rebate support is coordinated around the electrical scope; it is not a substitute for the permit or inspection.
Service Area
Serving Arvada and Jefferson/Adams County
We serve Arvada, CO and all surrounding Denver metro communities. Our team is based in Denver and operates throughout the Front Range, from Castle Rock to Longmont and everywhere in between. Contact us for a free estimate on your Arvada project.
How It Runs
01
Survey
02
Design
03
Build
04
Verify
DESIGN SERVICES
Discovery & Site Analysis
Needs + preference programming, site survey, as-built documentation, feasibility.
We walk, measure, and photograph your property — existing conditions, utilities, structure, and constraints. You get the as-built documentation and feasibility read that every later decision rests on.
Learn more →Concept Design & Space Planning
Schematic design, floor plan studies, layout options.
Your scope becomes schematic floor plans you can compare side by side — circulation, daylight, adjacencies, and what each option does to the budget. Layout decisions happen on paper, where changes are cheap.
Learn more →Architectural Design & 3D Renderings
Design development, materials + finishes, photorealistic visualization.
The chosen concept resolves into materials, finishes, fixtures, and lighting — with the automation layer drawn in. Photorealistic renderings let you walk the space and adjust before anything is priced.
Learn more →Construction Documents & Permitting
Full CD sets, structural + MEP engineering coordination, permit-ready drawings.
Approved designs become coordinated architectural, structural, and MEP sheets — the set your jurisdiction permits from and trades build from. We submit, track, and answer review comments.
Learn more →CONSTRUCTION
New Construction & Custom Homes
Ground-up homes and light commercial, dirt to keys.
Ground-up residential and light commercial builds — foundations through finishes, including modular and steel construction. One accountable builder from dirt to keys.
Learn more →Remodels & Additions
Kitchens, baths, basements, pop-tops, whole-home.
Kitchens, baths, basements, pop-tops, and whole-home renovations that respect the house you already have. We handle structure, permits, and the dust.
Learn more →Commercial Tenant Finish & Build-Outs
Shells to working spaces — retail, office, restaurant, school.
Raw shells become working spaces — showrooms, offices, restaurants, schools. Dealer-spec finishes, code compliance, and opening dates held.
Learn more →ADUs & Modular Construction
Backyard cottages, garage conversions, factory-built homes.
Backyard cottages, garage conversions, and factory-built homes — zoning, design, permits, and set. Denver’s ADU rules are a specialty, not a surprise.
Learn more →Outdoor Living & Patio Structures
Decks, pergolas, and dining patios built for Colorado weather.
Decks, pergolas, and dining patios engineered for Colorado sun, snow, and hail — structure, shade, and drainage done right the first time.
Learn more →TECHNOLOGY
Smart Home Automation
Lighting, shades, climate, audio, security — one interface.
Whole-home control of lighting, shades, climate, audio, and security from a single interface — Crestron, Lutron, Savant, and Control4 designed in, not bolted on.
Learn more →A/V Systems
Theaters, distributed audio, video walls, commercial sound.
Theaters, distributed audio, video walls, and commercial sound — designed, installed, and tuned by the same team for over 20 years.
Learn more →Control Systems
Custom programming — scenes and schedules that fit the space.
Every subsystem brought into one elegant interface — custom programming for homes and venues, with scenes and schedules that match how the space is actually used.
Learn more →Networking & Edge Compute
Enterprise Wi-Fi, structured cabling, racks, on-prem compute.
Enterprise-grade Wi-Fi, structured cabling, racks, and on-premise compute — the backbone that makes everything else reliable, including our own Barbot platform.
Learn more →Solar & Energy Storage
Solar arrays, Tesla Powerwall, EV charging — certified install.
Solar arrays, Tesla Powerwall, and EV charging designed and installed by a Tesla Energy Certified team — roof, electrical, and app in one scope.
Learn more →TRUSTED TO BUILD FOR
- Punch Bowl SocialFirst four locations
- Spectrum RetirementSenior living communities
- Denver HighlandsFirst modular custom home
Explore
Also serving
Explore