Plumbing for Denver Homes and Commercial Buildings

Install customer-supplied bidet seat or washlet on an existing toilet: remove old seat, mount seat, install T-valve on the toilet supply, connect and leak-test. Requires an existing GFCI outlet within cord reach for electric models. NOT included: the seat itself, new electrical outlet installation, hot-water line runs, or toilet replacement.

Install a dishwasher air gap (parts included) in an existing sink or countertop knockout hole, reroute the dishwasher drain hose through it, and test a drain cycle. NOT included: drilling new holes in stone or quartz countertops (stainless sink deck drilling is included), disposal replacement, or high-loop-only conversions.

Convert a hard-wired garbage disposal to cord-and-plug: install a switched outlet in the sink cabinet fed from the existing disposal circuit, install a cord kit on the disposal (parts included), and test. Makes future disposal swaps a 30-minute job. NOT included: new circuits from the panel, GFCI panel work beyond the outlet itself, disposal replacement, or plumbing changes.

Replace a leaking or non-frost-free exterior hose bib with a new frost-free sillcock (included), where the interior pipe connection is accessible from a basement, crawlspace, or utility area. Includes vacuum breaker per local code. NOT included: connections buried in finished walls or ceilings (variable scope — book a visit), pipe rerouting, or stucco/siding repair.

Run a new quarter-inch water line from an accessible cold-water source (under adjacent sink, basement, or crawlspace within ~25 feet) to the refrigerator, with a proper tee-and-ball-valve connection (no saddle valves), copper or braided line included, connected and leak-tested. NOT included: routes requiring wall or ceiling opening in finished spaces, refrigerator repair, or filter systems.

Replace a leaking or corroded under-sink trap and tailpiece assembly with new PVC or chrome components (parts included) at one sink, sealed and leak-tested. Covers kitchen or bath sinks with accessible under-cabinet plumbing. NOT included: in-wall drain pipe repair, cabinet floor repair from prior leaks, or garbage disposal work.

Remove existing sink or vanity and install a customer-supplied pedestal sink in the same location: mount basin to blocking/wall, set pedestal, install faucet and drain, connect to existing plumbing, seal and leak-test. Includes adding wall blocking if the stud bay is open or accessible. NOT included: the sink or faucet, plumbing relocation, drywall or tile repair behind the removed vanity, or paint.

Connection of a refrigerator ice maker/water dispenser to an existing accessible shutoff valve within 15 ft: new braided or PEX supply line (materials included), connection at the fridge, leak check under pressure, and line flush. Requires an existing functional fridge shutoff or accessible cold-water valve. Excludes installing a new tee/valve into supply plumbing (quoted separately), saddle valves (we replace, not install), in-door filter sourcing, and drywall penetration into finished walls.

Install a customer-supplied under-sink reverse osmosis system: mount the unit and storage tank, tee into cold supply, install the drain saddle on the sink drain, set the RO faucet in an existing hole (or drill stainless sink deck), pressurize, flush per manufacturer spec, and leak-test. NOT included: the RO system, drilling stone or quartz countertops, remote tank locations, or fridge-line tie-ins beyond 10 feet.

Remove old shower head, clean and re-tape the shower arm threads, and install a customer-supplied head or handheld kit, leak-tested. Includes shower arm replacement if the old arm is corroded (standard arm included). NOT included: the shower head itself, in-wall drop-ear repair if the fitting spins, or slide-bar installs into tile (book bath accessory SKU).

Replace shower handle, escutcheon, tub spout, and shower head with a customer-supplied trim kit that matches the existing in-wall valve brand and model, sealed and tested. NOT included: the trim kit itself, valve body replacement (variable scope — book a visit), cartridge replacement (add the cartridge SKU), or tile repair.

Replace a broken or non-sealing bathroom sink pop-up drain and stopper assembly, including the drain body, linkage, and gaskets (standard parts included), then leak-test. NOT included: matching designer finishes (customer supplies specialty drains), trap replacement (separate SKU), or vessel-sink grid drains.

Reroute of an existing above-grade exterior sump discharge line up to 25 ft (rigid PVC or corrugated pipe, materials included) to move water away from the foundation, with air gap/freeze-relief fitting at the exit and secured slope to daylight. Excludes buried lines, dry wells, work on the sump pump itself or interior plumbing, trenching through hardscape, and lines over 25 ft (quoted separately).

Replace a failed thermal expansion tank at the water heater (2 or 4.5 gallon tank included), pre-charge to match house pressure, support properly, and leak-test. Covers first-time installs where a tee already exists on the cold line. NOT included: water heater repair, repiping to create a connection point in hard-to-reach configurations, or PRV replacement (separate SKU — commonly paired).

Install a code-compliant thermostatic mixing valve at the water heater outlet (valve and fittings included) so the tank can run hotter for capacity while delivering scald-safe temps to fixtures; set and verify output temperature. Requires accessible copper or PEX at the heater. NOT included: water heater repair or replacement, point-of-use shower mixing valves, or recirculation loop work.

Pull the toilet, repair a broken or corroded closet flange using a repair ring, spanner flange, or push-in replacement as appropriate, then reset the toilet with a new wax ring and bolts and leak-test. NOT included: subfloor repair or rot remediation, drain pipe replacement below the flange, tile work, or a new toilet.

Remove old toilet seat (including seized or corroded bolts, which we cut off) and install a customer-supplied replacement seat, aligned and tightened. NOT included: the seat itself, bidet seats (separate SKU), or any tank/bowl work. Best value when added to another visit.

Pull and reset an existing toilet with a new wax ring (or waxless seal), new closet bolts, re-shim and level, recaulk the base, and leak-test. Fixes rocking toilets and base leaks with an intact flange. NOT included: flange repair (book the flange repair SKU if the flange is broken — we'll confirm on site), subfloor work, or internal tank parts.

Remove old slip-fit or threaded tub spout and install a matching customer-supplied or standard chrome replacement (standard spout included if not supplied), sealed and tested including diverter function. NOT included: in-wall copper stub-out repair if the pipe is damaged, valve or trim work (separate SKUs), or tile repair.

Install a customer-supplied single or dual-stage under-sink filter system with a dedicated drinking faucet in an existing sink hole or included deck drilling in stainless sinks, tee into the cold supply, flush cartridges, and leak-test. NOT included: the filter system, drilling stone or quartz countertops, reverse osmosis systems (separate SKU), or whole-house filtration.

Install a customer-supplied freestanding utility sink where laundry-area supply and drain connections already exist within reach: assemble legs, install faucet, connect supplies and P-trap to the existing standpipe or drain, and leak-test. NOT included: the sink or faucet, new drain or supply rough-in, pump-up drain systems, or tying into a drain more than 6 feet away.

Remove old bathroom sink faucet, install customer-supplied replacement, connect new supply lines (included), reconnect pop-up linkage, and leak-test. NOT included: the faucet itself, corroded/seized shutoff valve replacement (add the shutoff valve SKU), drain assembly replacement, or countertop drilling for a different hole pattern.

Replace both washing machine supply hoses with new braided stainless hoses (parts included), pull and reposition the machine, and leak-test under pressure. Requires working laundry shutoff valves. NOT included: valve or valve box replacement (separate SKU), drain hose or standpipe work, or machine repair.

Replace a leaking or seized laundry supply valve box with a new recessed outlet box with quarter-turn valves (parts included), connecting to existing copper or PEX in the wall cavity, plus new braided hoses to the machine and full leak-test. Includes cutting the access opening. NOT included: drywall patch and paint of the access opening, drain standpipe work, or repiping beyond the immediate connections.

Permitted like-for-like replacement of a 40-gallon atmospheric gas water heater, including unit, expansion tank, code-required fittings, haul-away, and the local permit. Power-vent, tankless, or relocation work is quoted separately.

Replace the pressure reducing valve (PRV) on the main line with a new regulator (included), set outlet pressure to 55-65 PSI, and verify with gauge readings at fixtures. Requires an accessible existing PRV location and working main shutoff. NOT included: main shutoff valve replacement if it fails to hold (added on site only with your approval), first-time PRV installs where none exists, or expansion tank (separate SKU — commonly paired).