DESIGN · BUILD · AUTOMATE
WHEAT RIDGE SERVICES
MEP Engineering in Wheat Ridge
Licensed MEP engineering services for Wheat Ridge and Jefferson County. Mechanical, electrical, and plumbing design.
- Full Design Lifecycle
- Construction & Tenant Finish
- Smart Home · A/V · Edge Compute
Mechanical, electrical, and plumbing design
FREE PLANNING TOOLS
Both tools are free and take a couple of minutes — start in either one.
EVERY PROJECT STARTS WITH DESIGN
Local Service
MEP Engineering Services in Wheat Ridge, Colorado
Autotelic provides professional MEP engineering services throughout Wheat Ridge and the surrounding Jefferson County area. Professional MEP engineering services including HVAC design, electrical load calculations, plumbing layouts, and energy code compliance. Whether you're in Wheat Ridge (central Jefferson County) or nearby communities, our team delivers quality workmanship backed by Colorado licensing and full insurance coverage.
Permit Thresholds
Wheat Ridge permit thresholds
- Code reference
- Retaining walls over 4' high (or supporting a surcharge) and other structural elements like decks or room additions explicitly require permits; any structural work in a remodel would qualify as an alteration requiring a permit.
- Code reference
- These requirements are enforced under the City of Wheat Ridge Municipal Code, Chapter 5, Article II, Division 2 (Building Permits).
- Use tax
- Per City Code Section 22-68, use tax is charged at 3.5% of 60% of the project valuation (60% of valuation is assumed to be materials subject to tax).Section 22-68
- Code reference
- Permit fees are based on the higher of the applicant’s valuation or the building official’s minimum (using ICC Building Valuation Data); a separate plan review fee (65% of the permit fee) applies where required.
Codes are amended regularly — verify current requirements with **City of Wheat Ridge Building Division (City of Wheat Ridge, Colorado) issues residential building permits.
Zoning & Dimensional Standards
Setback & dimensional standards in Wheat Ridge
Zone-district dimensional standards for Wheat Ridge, quoted verbatim from the Wheat Ridge Code of Ordinances (Ch.26 Zoning). Knowing your lot's district — and its setbacks, height, and coverage limits — is where every feasibility conversation starts.
A-1setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 30' (c) |
| Side Setback (min) | 15' |
| Rear Setback (min) | 15' (g) |
| Building Coverage (max) | 25% |
| Building Height (max) | 35' |
| Lot Area (min) | 1 acre |
| Lot Width (min) | 140' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) A-1 setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
A-2setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 30' (c) |
| Side Setback (min) | 15' |
| Rear Setback (min) | 15' (g) |
| Building Coverage (max) | 25% |
| Building Height (max) | 35' |
| Lot Area (min) | 1 acre |
| Lot Width (min) | 140' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) A-2 setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-1setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 30' (c) |
| Side Setback (min) | 15' |
| Rear Setback (min) | 15' |
| Building Coverage (max) | 25% |
| Building Height (max) | 35' |
| Lot Area (min) | 12,500 sf |
| Lot Width (min) | 100' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-1 setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-1Asetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (c) |
| Side Setback (min) | 10' |
| Rear Setback (min) | 15' (h) |
| Building Coverage (max) | 30% |
| Building Height (max) | 35' |
| Lot Area (min) | 9,000 sf |
| Lot Width (min) | 75' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-1A setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-1Bsetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (d) |
| Side Setback (min) | 5' (e) |
| Rear Setback (min) | 10' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 7,500 sf |
| Lot Width (min) | 60' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-1B setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-1Csetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 20' (d) |
| Side Setback (min) | 5' |
| Rear Setback (min) | 5' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 5,000 sf |
| Lot Width (min) | 50' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-1C setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-2setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (d) |
| Side Setback (min) | 5' (e) |
| Rear Setback (min) | 10' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 9,000 sf |
| Lot Width (min) | 75' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-2 setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-2Asetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (d) |
| Side Setback (min) | 5' (d) |
| Rear Setback (min) | 10' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 7,500 sf |
| Lot Width (min) | 60' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-2A setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-3setback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (e) |
| Side Setback (min) | 5' |
| Rear Setback (min) | 10' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 7,500 sf |
| Lot Width (min) | 60' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-3 setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
R-3Asetback & dimensional standards
| Standard | Requirement |
|---|---|
| Front Setback (min) | 25' (e) |
| Side Setback (min) | 5' |
| Rear Setback (min) | 10' |
| Building Coverage (max) | 40% |
| Building Height (max) | 35' |
| Lot Area (min) | 7,500 sf |
| Lot Width (min) | 60' |
Wheat Ridge Code of Ordinances (Ch.26 Zoning) R-3A setback standards (Ch.26 Art.II district standards tables) — effective 2025-01-27 · View the code
Verify current requirements with the jurisdiction — informational reference only. Standards vary by overlay, lot, and use; we confirm the exact rules for your property during feasibility.
text
What MEP coordination covers
MEP engineering coordination on Denver-metro projects means bringing design professionals into mechanical, electrical, and plumbing scopes: HVAC loads and duct layouts, electrical one-lines and panel schedules, plumbing risers, and energy-code documentation. The general contractor coordinates schedule, permitting, and construction around sealed drawings. A municipally licensed Denver general contractor does not replace the engineer of record; it coordinates design professionals and the build team. Cost is project-specific and depends on building type and system complexity.
text
When CPD wants engineered packages
City and County of Denver Community Planning and Development asks for engineered drawings, calculations, specifications, and energy-code information when commercial or multifamily work includes electrical, mechanical, or plumbing changes. Additions typically need building plus electrical, mechanical, plumbing, and Sewer Use and Drainage (SUDP) review through DOTI. Equipment replacements can trigger mechanical review for capacity, makeup air, and exhaust.
text
Permits and who coordinates the work
MEP packages are submitted through Denver CPD e-permits with the building permit. Colorado DORA regulates electrical and plumbing licensing. Cities and counties license general contractors. Colorado has no statewide general contractor license. Autotelic acts as a municipally licensed Denver general contractor and coordinates licensed specialty trades plus the design professionals required for the project.
text
What buyers should prepare
Project type (tenant finish, addition, equipment swap), any existing drawings, and known panel, HVAC, or plumbing capacity limits.
FAQ
Common questions
Do MEP changes need engineered drawings in Denver?
Often yes for commercial and multifamily work. CPD commercial plan review lists electrical, mechanical, and plumbing as drawing-review items when those systems change.
Who handles MEP permits and licensing?
A municipally licensed Denver general contractor coordinates the project, design professionals, and specialty trades. Colorado has no statewide general contractor license.
Is the GC the MEP engineer of record?
No. Sealed mechanical, electrical, and plumbing design is provided by design professionals who seal the documents. The GC coordinates construction around those documents.
When is an SUDP involved?
Denver DOTI reviews Sewer Use and Drainage with most building-permit packages, including many remodels, because fixture or drainage changes can affect sewer use.
What information helps define scope?
Desired system changes, existing drawings if any, photos of equipment and panels, and city or county.
Service Area
Serving Wheat Ridge and Jefferson County
We serve Wheat Ridge, CO and all surrounding Denver metro communities. Our team is based in Denver and operates throughout the Front Range, from Castle Rock to Longmont and everywhere in between. Contact us for a free estimate on your Wheat Ridge project.
How It Runs
01
Survey
02
Design
03
Build
04
Verify
DESIGN SERVICES
Discovery & Site Analysis
Needs + preference programming, site survey, as-built documentation, feasibility.
We walk, measure, and photograph your property — existing conditions, utilities, structure, and constraints. You get the as-built documentation and feasibility read that every later decision rests on.
Learn more →Concept Design & Space Planning
Schematic design, floor plan studies, layout options.
Your scope becomes schematic floor plans you can compare side by side — circulation, daylight, adjacencies, and what each option does to the budget. Layout decisions happen on paper, where changes are cheap.
Learn more →Architectural Design & 3D Renderings
Design development, materials + finishes, photorealistic visualization.
The chosen concept resolves into materials, finishes, fixtures, and lighting — with the automation layer drawn in. Photorealistic renderings let you walk the space and adjust before anything is priced.
Learn more →Construction Documents & Permitting
Full CD sets, structural + MEP engineering coordination, permit-ready drawings.
Approved designs become coordinated architectural, structural, and MEP sheets — the set your jurisdiction permits from and trades build from. We submit, track, and answer review comments.
Learn more →CONSTRUCTION
New Construction & Custom Homes
Ground-up homes and light commercial, dirt to keys.
Ground-up residential and light commercial builds — foundations through finishes, including modular and steel construction. One accountable builder from dirt to keys.
Learn more →Remodels & Additions
Kitchens, baths, basements, pop-tops, whole-home.
Kitchens, baths, basements, pop-tops, and whole-home renovations that respect the house you already have. We handle structure, permits, and the dust.
Learn more →Commercial Tenant Finish & Build-Outs
Shells to working spaces — retail, office, restaurant, school.
Raw shells become working spaces — showrooms, offices, restaurants, schools. Dealer-spec finishes, code compliance, and opening dates held.
Learn more →ADUs & Modular Construction
Backyard cottages, garage conversions, factory-built homes.
Backyard cottages, garage conversions, and factory-built homes — zoning, design, permits, and set. Denver’s ADU rules are a specialty, not a surprise.
Learn more →Outdoor Living & Patio Structures
Decks, pergolas, and dining patios built for Colorado weather.
Decks, pergolas, and dining patios engineered for Colorado sun, snow, and hail — structure, shade, and drainage done right the first time.
Learn more →TECHNOLOGY
Smart Home Automation
Lighting, shades, climate, audio, security — one interface.
Whole-home control of lighting, shades, climate, audio, and security from a single interface — Crestron, Lutron, Savant, and Control4 designed in, not bolted on.
Learn more →A/V Systems
Theaters, distributed audio, video walls, commercial sound.
Theaters, distributed audio, video walls, and commercial sound — designed, installed, and tuned by the same team for over 20 years.
Learn more →Control Systems
Custom programming — scenes and schedules that fit the space.
Every subsystem brought into one elegant interface — custom programming for homes and venues, with scenes and schedules that match how the space is actually used.
Learn more →Networking & Edge Compute
Enterprise Wi-Fi, structured cabling, racks, on-prem compute.
Enterprise-grade Wi-Fi, structured cabling, racks, and on-premise compute — the backbone that makes everything else reliable, including our own Barbot platform.
Learn more →Solar & Energy Storage
Solar arrays, Tesla Powerwall, EV charging — certified install.
Solar arrays, Tesla Powerwall, and EV charging designed and installed by a Tesla Energy Certified team — roof, electrical, and app in one scope.
Learn more →TRUSTED TO BUILD FOR
- Punch Bowl SocialFirst four locations
- Spectrum RetirementSenior living communities
- Denver HighlandsFirst modular custom home
Explore